ServoShop Checkout |  Home
Futaba  |  Hitec  |  JR  |  Tower Pro  |  PowerHD  |  Spektrum  |  Savox  |  Contact Us  |  Latest News  |  SecurityMetrics Credit Card Safe


Similar Products



The Wings Maker Panther Combo REF GE032C

The Wings Maker DF-032C Panther (combo NOT Pre-Assembled) - Delta manufactured from tough EPO Foam

Nigel Hawes from RCM&E - Probably one of the best value EDF sport models on the market today

This is a superb model, that is easy to fly and launch. Being a delta it's easy to fly slowly, but equally at home when you open the taps.

A full power dive is great fun, as it goes like the proverbial bat out of hell when you want it to. You will need to switch to 'low rates' on such occasions, as it can be a little twitchy at really high speed.

Can be hand launched or use the included dolly (though you may want to put some bigger wheels on if flying off grass)

The manufacturer recommends using a 30 Amp ESC, however the motor/fan can draw in excess of 37 Amps with a good battery, so we recommend using a 40 to 50 Amp ESC.

Warning if you watch the videos you will want one!

  • The Wings Maker's electric jet series.
  • Hot aerobatics at high speed and relaxing flying at low speed.
  • Lightweight and strong EPO foam provides structural strength and rigidity.
  • 'Combo' Version - includes servos, motor & fan unit
  • Code No. : GE032C
  • Wing Span : 33 in / 850 mm
  • Wing Area : 299 sq in / 19.3 sq dm
  • Flying Weight : 24 oz / 680 g
  • Fuselage Length : 26.5 in / 675 mm

If you need extra servos or spare servos for Wings Maker - then click the link to take you to the Wings Maker Servos

The manufacturer recommends using epoxy glue to put this kit together. However from our own experience we did not find epoxy the best type of glue for EPO and we recommend a cyano glue such as Bob Smiths Super Gold or Gold Cyno or Multiplex Zacki adhesive. Many standard forms of Cyno adhesives can also be used, but we always advise testing unknown glues on scrap foam before committing them to use.

picture

Price

£89.99 Each

picture



Tower Pro H40 Amp ESC 50AMP Burst Heli/Aero

H40A ESC for heli & airplane

Specs

  • Dimensions: 70x31x11mm
  • Burst Rate (15sec): 50A
  • BEC Current: 1.5A
  • Voltage: 7.4-11.1V (2-3 cell Lipo/5-10 NiMH,NiCd)
  • Weight: 47g

Please note this is a genuine Tower Pro item When comparing prices do consider you may be buying copies. This item is Original Tower Pro manufacture 12 month U.K warranty - against manufactured defects terms and conditions do apply.

picture

Price

£16.99 Each
2 for £33.00

picture


Customers Also Considered



The Wings Maker J10B Fighter Kit Ref GE034

The J-10B Fighter - now available in the U.K at SWM and ServoShop! Please note this is the kit version and other items are needed to complete this model.

The videos below show the J10 flying in various conditions. In one video you will get to see how the J10 handles the wind and in the other videos there's some great general club flying and J10 chases, Warning if you watch the videos you will want one!

  • 'Kit set' Version
  • The Wings Maker's electric jet series
  • Hot aerobatics at high speed and scaled flying at low speed
  • Lightweight and strong EPO foam provides structural strength and rigidity
Code No.:GE034
Wing Span:28.7 in / 730 mm
Wing Area:310 sq in / 20 sq dm
Flying Weight:28.5 oz / 805 g
Fuselage Length:42.7 in / 1085 mm
Requires:Outrunner Motor 28/31 KM0283110 and Ducted Fan Propulsion Unit PL6800010, 4-channel "mixing radio" (elevator and aileron) w/ 3 micro servos SV2031, 40A (burst 50A) brushless ESC and 3 cells 11.1V 20C 2100mAh battery and charger

ESC Specifications - Please Note

Although the manufacturer recommends a 30/35 Amp ESC for this aircraft, we have found that the World Models 70mm Fan unit can draw in excess of 37 Amps on a good battery. Following many flights with our own models we would recommend a 40 to 50 amp ESC on a 3 Cell Set Up and if using the 4 Cell Turbo Motor and TWM Fan we recommend a 60 to 70 amp ESC.

As with all final fix motor installations you should check the ESC used is adequate for your individual set up

From our own experience we did not find epoxy the best type of glue for EPO and we recommend Bob Smiths Super Gold or Gold Cyno or Multiplex Zacki adhesive. Many standard forms of Cyno adhesives can also be used, but we always advise testing unknown glues on scrap foam before committing them to use.

picture

Price

£54.99 Each

picture



The Wings Maker J10B Fighter Combo Set Ref GE034C

J-10B Fighter (Combo) - This is the Combo Version.

For a Ready Assembled Combo and for a J10 Kit Only (No Fan or Motor) see seperate listings.

The videos below show the J10 flying in various conditions. In one video you will get to see how the J10 handles the wind and in the other videos there's some great general club flying and J10 chases, Warning if you watch the videos you will want one!

If you need extra servos or spare servos for Wings Maker - then click the link to take you to the Wings Maker Servos

  • 'Receiver ready combo set' Version
  • The Wings Maker's electric jet series
  • Hot aerobatics at high speed and scaled flying at low speed
  • Lightweight and strong EPO foam provides structural strength and rigidity
  • Code No. : GE034C
  • Wing Span : 28.7 in / 730 mm
  • Wing Area : 310 sq in / 20 sq dm
  • Flying Weight : 28.5 oz / 805 g
  • Fuselage Length : 42.7 in / 1085 mm
  • Requires : 4-channel "mixing radio" (elevator and aileron), 40A (burst 50A) brushless ESC and 3 cells 11.1V 20C 2100mAh battery and charger

ESC Specifications - Please Note

Although the manufacturer recommends a 30/35 Amp ESC (when running a 3-cell setup) for this aircraft, we have found that the fan unit will draw over 37 Amps with a good battery. Following many flights with our own models we would recommend a 40 to 50 amp ESC on a 3 Cell Set Up and if using the 4 Cell Turbo Motor and TWM Fan we recommend a 60 to 70 amp ESC.

As with all final fix motor installations you should check the ESC used is adequate for your individual set up

Although the manufacturer recommends using epoxy to put the kit together, from our own experience we did not find this type of glue to be particularly suitable for EPO and we recommend Bob Smiths Super Gold or Gold Cyno or Multiplex Zacki adhesive. Many standard forms of Cyno adhesives can also be used, but we always advise testing unknown glues on scrap foam before committing them to use.

picture

Price

£99.99 Each

picture
 
Privacy statement Terms & conditions © Steve Webb Models Limited 2017. Postage & packing Contact us